Top 13 how to tear down a load bearing wall

Below is the best information and knowledge about how to tear down a load bearing wall compiled and compiled by the hkfindall.com team, along with other related topics such as:: Load bearing wall and joists, removing a load-bearing wall before and after, replace load-bearing wall with columns cost, how much of a load-bearing wall can be removed, load bearing wall removal calculations, load bearing wall removal before and after, removing load bearing wall without permit, load bearing wall removal contractors.

how to tear down a load bearing wall

Image for keyword: how to tear down a load bearing wall

The most popular articles about how to tear down a load bearing wall

How to Remove a Load Bearing Wall – Design Everest

  • Author: designeverest.com

  • Evaluate 4 ⭐ (39417 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Remove a Load Bearing Wall – Design Everest To remove a load-bearing wall, construction will likely cost between $1,200 and $3,000 if you have a single-story home, and between $3,200 and $10,000 for multi …

  • Match the search results: The first thing to do is figure out if the wall is a partition wall or a load-bearing wall. A non-load-bearing or partition wall doesn’t support the load of the house and its purpose is solely to divide spaces. A load-bearing wall is a major provider of support for the roof and/or floor, ultim…

  • Quote from the source:

How to remove a load bearing wall – DIY kitchen renovation

  • Author: prettypassive.com

  • Evaluate 3 ⭐ (20233 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to remove a load bearing wall – DIY kitchen renovation How to remove a load bearing wall – on a budget* · find your new hole width · calculate the beam span and load · build a “sacrificial wall” to hold …

  • Match the search results: I am so happy we removed that wall. We lost some privacy (I lost wall space for decor and can’t hide a messy kitchen anymore) but the space is bigger, brighter, and gave me the multiple exit routes I needed for my sanity!!

  • Quote from the source:

Can I Remove This Wall? Removing a Load-Bearing Beam

  • Author: www.familyhandyman.com

  • Evaluate 4 ⭐ (35841 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Can I Remove This Wall? Removing a Load-Bearing Beam If you plan to remove a bearing wall, we recommend hiring a structural engineer. An engineer will inspect the house, calculate the size of the …

  • Match the search results: Only some of your walls are needed to hold up your house. These are called bearing walls. The rest of the walls, the partition walls, are simply there to divide rooms. You can remove either type of wall, but if the wall is load bearing, you have to take special precautions to support the structure d…

  • Quote from the source:

How Much of a Load-Bearing Wall Can Be Removed? | HGTV

  • Author: www.hgtv.com

  • Evaluate 3 ⭐ (12577 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How Much of a Load-Bearing Wall Can Be Removed? | HGTV HGTV dives into load-bearing walls, helping you learn what to look for before you remove one, and understanding how much of a load-bearing wall you can …

  • Match the search results: Home renovation is no light matter, especially when it involves heavy lifting to remove or replace walls. As homeowners continue to embrace open concepts and look for ways to expand and better utilize spaces in their home, removing walls is often at the forefront of an ambitious project. There are a…

  • Quote from the source:

Can You Remove a Load-Bearing Wall? | HowStuffWorks

  • Author: home.howstuffworks.com

  • Evaluate 4 ⭐ (33329 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Can You Remove a Load-Bearing Wall? | HowStuffWorks You’ve determined that the wall you want to remove is load-bearing — so now what? We’ll explore the nitty-gritty of bearing wall removal on …

  • Match the search results: The first step in is to remove the drywall and strip the wall down to its skeleton. Since load-bearing walls carry a house’s worth of weight, they’re usually built from sturdier materials than other types of walls. While non-bearing walls may be framed with wood, bearing walls are usually reinforced…

  • Quote from the source:

How to Remove a Load-Bearing Wall – This Old House

  • Author: www.thisoldhouse.com

  • Evaluate 4 ⭐ (33709 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Remove a Load-Bearing Wall – This Old House Steps for Removing a Load-Bearing Wall · Install temporary 2×4 braces on either side of wall to support the ceiling above. · Use reciprocating saw to cut through …

  • Match the search results: In this video, This Old House general contractor Tom Silva shows how to safely cut open up a wall.

  • Quote from the source:

Taking Out A Load-Bearing Wall | Everstead

  • Author: everstead.com

  • Evaluate 3 ⭐ (17376 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Taking Out A Load-Bearing Wall | Everstead The price to remove a load-bearing wall in a single-story home is about $1,200 to $5,000, depending on what type and how many beams are needed.

  • Match the search results: Load-bearing walls are a major support structure in your home. They carry the weight of the roof or upper floor level. A non-load-bearing wall is often called a partition wall and serves only to separate rooms. When your home was built and designed, the architects and engineers planned the support s…

  • Quote from the source:

Cost of Structural Engineer For Load Bearing Walls

  • Author: jacobmartin.com

  • Evaluate 3 ⭐ (9592 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Cost of Structural Engineer For Load Bearing Walls If you plan to add, move, or remove a load-bearing wall, structural engineers help devise a plan of action while ensuring the structural stability and …

  • Match the search results: Load-bearing walls need to be inspected before taking them down as these walls support the structural weight of a building. Unlike a non-load-bearing or curtain wall, its function is not only to divide rooms. The possibility of potential life-threatening collapse is evident in some cases if the stru…

  • Quote from the source:

How To Remove A Load-Bearing Wall – BestLife52

  • Author: bestlife52.com

  • Evaluate 4 ⭐ (22348 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How To Remove A Load-Bearing Wall – BestLife52 Remove The Old Wall Studs … With the ceiling firmly braced by the temporary walls, knock out the old wall studs with a 2-lb. sledge or a hammer.

  • Match the search results: As you size up this project, keep in mind that your house has two kinds of walls; “non-bearing” walls, which support little weight, and “bearing” walls, which support a lot of weight,

  • Quote from the source:

How to Remove Load Bearing Walls in Sacramento?

  • Author: www.houseidea.com

  • Evaluate 3 ⭐ (7249 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Remove Load Bearing Walls in Sacramento? Identifying and removing the load-bearing wall is crucial to avoid collapsing the entire house. Here we will discuss how to remove a …

  • Match the search results: The foremost thing is to identify whether the wall you are planning on removing is a partition wall or a load-bearing one. The partition wall is used to divide the house’s space and does not support the roof. In comparison, a load-bearing wall is the one that supports the entire load or the roof by …

  • Quote from the source:

10 signs of load-Bearing walls: How to knock down a house wall

  • Author: www.check4lead.com

  • Evaluate 4 ⭐ (35359 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about 10 signs of load-Bearing walls: How to knock down a house wall That is why you cannot remove a load-bearing structure without any replacement support in place. It will affect the structural integrity of …

  • Match the search results: Because the work involved costs more to remove a load-bearing wall, special precautions are needed before and during. Expect the price of its removal to start from $10,000 for walls in a single-story home. It’ll cost as much as $30,000 for walls in homes with two stories or more.

  • Quote from the source:

Open Spaces – What to Know Before Tearing Down a Wall

  • Author: www.tankersleybuilds.com

  • Evaluate 3 ⭐ (12773 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Open Spaces – What to Know Before Tearing Down a Wall At this point, if you suspect a wall is load bearing I would advise working with a reputable licensed contractor. The framing should be exposed …

  • Match the search results: If a wall is perpendicular to the roof trusses and you suspect it might be load bearing, the next indication would be to examine the framing. At this point, if you suspect a wall is load bearing I would advise working with a reputable licensed contractor. The framing should be exposed by removing th…

  • Quote from the source:

Tearing Walls DOWN! – Art Tile & Renovation

  • Author: austin-tile-pro.com

  • Evaluate 3 ⭐ (3246 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Tearing Walls DOWN! – Art Tile & Renovation Getting rid of a load bearing wall is pretty simple in theory — simply replace the wall with a post and beam strong enough to support the …

  • Match the search results: The original wall framing had an extra set of ceiling headers that made the total wall width 6-in. So, to eliminate the need for a whole lot of ceiling patching (and therefore keep labor costs down), two additional 2x10s (milled to 8-1/2″ depth) sistered to the LVL beam matched the original 6-…

  • Quote from the source:

Multi-read content how to tear down a load bearing wall

ViafiveWhen planning my kitchen remodel, I had strong feelings about removing the main wall that separates the kitchen and living room. But every time I share my vision with a guest, I get a “oooo, you better make sure the object isn’t charged” and I put all my energy into not keeping an eye on it.

Nothing kills renewal vibes more than structural issues. Not only because sometimes they can’t achieve their goals, but also because opponents show up too quickly and decide to crush your dreams.

Removing a load-bearing wall is not uncommon and doesn’t require the stress everyone thinks it deserves.

Please read it again.

A lot of negative words were wasted on me because you better believe I removed that load-bearing wall. And it’s incredibly cheaper than anyone has ever estimated and easier than people think!

OG Wall:

The load bearing wall - before - not the worst, and honestly didn't NEED to go, but If I really want it back, It could be done. The inside of my load bearing kitchen wall - BYE

She served a good purpose. The open living/dining room concept is overrated by some, but our kitchen wasso sadthat it was completely gutted anyway. And I really wish I had a chance to bust this asshole and go through the whole process! (Nothing)

The paint color is Sherwin Williams Naive Peach, by the way. I still love this color and need it back!

We painted the kitchen cabinets on my first maternity leave and worked on a great ’70s kitchen (complete with sloppy floors, tiled wallpaper, and musty-smelling wood cabinets). Not to mention that the floating stove has no real home. It drives me crazy and might be part of the reason why I’m not upset to see the wall disappear.

Fix my kitchen with horns

Before this whole process even started, I thought about my design and started clearing this place (the cupboard on the left wall is gone. No one can stop me at this point, lol.

tearing down a load bearing wall - diy DIY load bearing wall removal: step one - stripping it to the studs

I like colors more, I like tearing things up more. For the record, there is no better cure for PMS.

How to remove a load-bearing wall – on a budget*

Sure this wall took the charge, but I’ve seen enoughUpper fixatorand remember Jo said something like “do it” whenThe design is worth it. Obviously, it takes a team of many boys to make it happen, and in my case, I have my husband, my father, my brother and my cousin.

My cousin is a freelance curator of all construction trades and he guided me every step of the way. I am one of those peopleneed to understand how things workbecause it’s easier to check the task when I can see the work in progress. The first thing to do is therefore to decide on the size of the new opening. The new hole in my house will be 14 feet wide.

  1. find your new hole width
  2. calculate
  3. beam span and load
  4. build a “sacrifice wall” to hold loads while removing existing structural supports
  5. remove all drywall/plaster, studs and headers on the way to your new beam!!
  6. buy or design the beam
  7. beam installation
  8. remove the wall of sacrifices (and save the wood for later)
  9. drywall around beams and studs

Measure your new bearing wall replacement hole

Looking at the IKEA kitchen plans I’ve worked on (and redone, edited, and re-edited), I find the size of the opening is very well visualized. This is the full length of the new opening, but you need to consider the width of the many 2x4s that will hold the beam. This number becomes more obvious after the next step, but having a general idea of ​​the new hole (or – a few feet on each side) should get you some proper comparisons. I want an 11 foot hole.

Calculation of beam span and load

The load-bearing wall doesn’t just disappear, it’s replaced with a super-strong beam that will support the load (get it?). My 11 foot hole is centered with the roof yard, so our new beams support the roof.

Believe it or not, there are simple formulas for calculating the mass a beam must support. And of course yesonline calculatormake it easier. All you need to know is the roof width and some general details about your home.

We have one of the easiest structures to replace a bearing wall. A floor does not have to worry about snow. However, you better be more generous with your calculations and overestimate the load. Bigger bundle with more support is awesome and helps me sleep better at night!

Plus, I appreciate an experienced cousin *cough* taking action. Two heads are better than one!

Additional Note:

No load-bearing wall is created equal, but they all follow the same process. The biggest difference between mine and yours is that your ceiling is designed to stay the same. This is the one thing you can’t expect a stranger to tell you on the internet!

Therefore, I strongly recommend that you hire a subcontractor/structural engineer with reliable experience in the field to confirm the “load” and provide perspective on the minimum required to maintain the structural integrity of the house (then add strength!!).

Build a wall of sacrifices to temporarily hold the charge

12 approximately 2x4s are used to make internal studstransition.My cousin was hesitant to let me “waste money” building the wall we were about to knock down, but I assured him that I would find something to do with them (and yes!). More on that later!

the sacrificial - dead wall for interim support before the new load bearing BEAM goes in

I would say this wall was drilled into the hardwood floor and ceiling. Those holes have since been patched, but that was another point my cousin was afraid to make. Naturally, I’m happy to do anything and everything to break down this wall (and I recently discoveredmy obsession for wood pulp).

Even better, we were finally able to attach a liner to something super strong and keep the kitchen clutter free.

RELATED: Frugal DIY Hardwood Floor Redecoration for Beginners

Clear all drywall/plasterboard, studs and headers in the way of your new beam!!

Sorry !!! In fact, yes! Most of this step is complete, but there is some debris in the way that needs to be sawed through before going any further. I like to erase the bullshit and fantasize about a fresh and open future.

Also, we had to clean everything up to make sure the structure would work as I hoped. Unfortunately that didn’t work out…and my loss of 12 minutes had to be reduced to 11 due to the shoving position on the floor.

With all the weight of the roof supported by the beams (held up by a number of 2x4s), we had to make sure these 2x4s were resting solidly on solid ground. They didn’t succeed and I had to change my plans by more than a foot… I’m still a little sad about that. It’s good now.

Purchasing / Harness Engineer

Everyone tells me “you’ll need to design a beam!” and they make it look scary. Oursdesign beam(instructed by the computer used) is2 2″x12’x13 with a piece of 1/4 plywood sandwiched between…Almost without sophistication.

Hardware stores will also sell metal beams, I guess that’s great but more expensive?

Anyway, I’m glad I didn’t let this discussion of beam engineering distract me from that dreamy hole in my house. But since we cut off some of the width of our original hole, I was able to save a 1×1 “sandwich” that I like to have as a home renovation moment.

Install beams

I’m not involved in that except to “manage” and help them see what I saw while it’s all going on. To protect me, they won’t accept my help. ‍♀️

It’s SNUG which is great but it’s hard to watch with a super heavy wood sandwich ready to crush my family.

However, she managed to get in after a few gentle massages and a harsh conversation.

Our engineered beam to replace a load bearing wall - 2 2x12x16 southern pine boards with plywood in between installing the engineered beam and replacing the load bearing wall

Remove the sacrifice wall (and save the wood for later)

with the new beam in place, my husband removed the sacrificial wall stud by stud removing the sacrificial wall stud by stud

Go but do not forget! I stacked these posts in a corner and moved them around the house for MONTHLY before taking them to work. But honestly, what else would I do? Casual?! WTF?

My husband calls me a hoarder, but I can’t let this wood die in vain. I finally used it to makemy built-in window bench ❤️

Drywall around beams and studs

Finishing steps. It’s not really part of the load bearing wall removal process because it’s just another step in the renovation process. Once the beams are completely installed and the temporary wall is removed,measures are taken.

finishing up the load bearing wall is as plain as drywall, and the edges were mudded instead of framed with wood. drywalling around the new beam! eek!

the finished product - removed load bearing wall

To wrap up

I’m glad we removed that wall. We’ve lost some privacy (I’ve lost wall space to decorate and can’t hide a messy kitchen anymore) but the space is bigger, brighter and gives me several of the exits including I need to stay awake. Apple!!

Price alreadyvery reasonable,but it should be remembered that the expression “very expensive” is purely subjective. Overall includes hourly work, walls of sacrifice, and super sophisticationdesign beam,removal and replacement cost less than $600.In my opinion, it is not expensive at all. Just another side of the $10,000 kitchen remodeling belt!

More than anything, I am happy to have played such an active role in this process. Knowing the details of these projects makes future projects easier to process AND evaluate. Because my biggest animal payscharge of ignorancefor everything I buy, by having first-hand experience with the traditional “out of my reach” I am able to bypass incidentals and have a greater say in creating its vision .

Go ahead, call me the controller. It’s probably not too far.

Anyway, increasing the value of my home is just another reason for me to increase my net worth, and when I save money to do so,The return on investment is enormous.

Removing a load bearing wall DIY - the cheapest way to open a kitchen up to the living room. Kitchen renovation ideasDIY wall removal - affordable kitchen renovation ideas for removing a load bearing wall and opening up a kitchen

Related

Popular questions about how to tear down a load bearing wall

Can you remove a load-bearing wall yourself?

Absolutely. While some people may tell you that you can tear down a load-bearing wall yourself. This is not a DIY project. Removing a load-bearing wall on your own can result in all sorts of costly mistakes, which can damage your home’s structure considerably.

How do you break a load-bearing wall?

Do I need permission to remove a load-bearing wall?

As a general rule, you don’t need planning permission for removing internal walls. But, if you are renovating a listed building, then you need consent for any external or internal work. You may also need your council to approve the work if it is load-bearing.

Do I need a structural engineer to remove a load-bearing wall?

Usually, the removal of a load-bearing wall can be completed with a building notice, but the inspector may instruct you to hire a structural engineer who can specify an appropriate beam or lintel before they will grant approval.

What happens if you knock out a load-bearing wall?

Removing a load bearing wall may create structural problems in a home, including sagging ceilings, unleveled floors, drywall cracks, and sticking doors.

How can you tell if a wall is load-bearing without removing drywall?

To determine if a wall is a load-bearing one, Tom suggests going down to the basement or attic to see which way the joists run. If the wall is parallel to the joists, it’s probably not load-bearing. If the wall is perpendicular, it’s most likely load-bearing.

How do you knock down a wall between two rooms?

Can a single brick wall be load bearing?

What is a loadbearing wall? Walls which support floor joists or other walls above are loadbearing. Bed recess, corridor walls and other walls which run parallel to the back and front walls of a tenement are normally loadbearing. Both brick and timber stud walls may be loadbearing.

How much does it cost to remove a non load-bearing wall?

The average cost to remove a non-load-bearing wall is $500 to $2,000. Removing a load-bearing wall costs $4,000 to $10,000 for a single-story house, and between $9,000 and $15,000 for a multi-story home.

How do you temporarily support a load-bearing wall?

How far apart can load-bearing walls be?

Based on the current sizing of lumber, and modern construction practices, 16″ was determined to be the right spacing between wall studs for residential load conditions. (There are exceptions, of course, as varying construction materials allow for different specifications.)

How do you build a support beam for a load-bearing wall?

Are partial walls load bearing?

Is a Partial Wall Load-Bearing? If the wall is a partial wall, meaning it stops short of an adjacent wall, it may or may not be load-bearing. For example, the builder may have installed a microlam beam to span across the opening and carry the load above.

Are shower walls load bearing?

Unless it’s an external wall or the shower is virtually in the center of the home, structural engineers rarely build load-bearing walls in showers. It is practicable to install the load-bearing wall where the greatest structural load is. Therefore the overall structure of a building is supported by load-bearing walls.

Are interior walls load bearing?

Check the foundation — If a wall or beam is directly connected to the foundation of your house, it is load bearing. This is extremely true for houses with additions, as even though these walls may be interior now, they were previously exterior walls, and are extremely load bearing.

Video tutorials about how to tear down a load bearing wall

keywords: #ThisOldHouse, #AskThisOldHouse, #DIY, #HomeImprovement, #DIYIdeas, #Renovation, #RenovationIdeas, #HowToFix, #HowToInstall, #HowToBuild, #Episode, #TVShow, #TomSilva, #loadbearingwall, #cutopenwall, #wall, #DoItYourselfnintendo, #home, #cartoon, #cops, #games, #house, #Animation, #tomsilvathisoldhouse, #tomsilvahouse, #tomsilvaconstruction, #tomsilvatools, #tommysilva

This Old House general contractor Tom Silva shows how to safely cut open up a wall. (See below for a shopping list and tools.)

SUBSCRIBE to This Old House:

-http://bit.ly/SubscribeThisOldHouse

Shopping List for How to Remove a Load-Bearing Wall:

– 2x4s [

-https://amzn.to/2WOvcEx],

– 2x8s [

-https://amzn.to/2w5zawY]

– construction adhesive [

-https://amzn.to/2JSjCox],

– assorted drywall screws [

-https://amzn.to/2YzTJhm]

Tools for How to Remove a Load-Bearing Wall:

– hammer [

-https://amzn.to/2HxNQds]

– reciprocating saw [

-https://amzn.to/2YEZOJn],

– power miter saw [

-https://amzn.to/2HpDBJx],

– drill/driver [

-https://amzn.to/2VvOsp8],

– caulking gun [

-https://amzn.to/2WReFQb],

– wet/dry vacuum [

-https://amzn.to/2w5iGEZ],

About This Old House TV:

This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WETA Washington, DC.

Follow This Old House and Ask This Old House:

Facebook:

-http://bit.ly/ThisOldHouseFB

Twitter:

-http://bit.ly/ThisOldHouseTwitter

-http://bit.ly/AskTOHTwitter

Pinterest:

-http://bit.ly/ThisOldHousePinterest

Instagram:

-http://bit.ly/ThisOldHouseIG

-http://bit.ly/AskTOHIG

Tumblr:

-http://bit.ly/ThisOldHouseTumblr

For more on This Old House and Ask This Old House, visit us at:

-http://bit.ly/ThisOldHouseWebsite

How to Remove a Load-Bearing Wall | This Old House

-https://www.youtube.com/user/thisoldhouse/

keywords: #loadbearingwall, #removingabeam, #construction, #remodeling, #remodel, #tipsandtricks, #buildingahouse, #home, #renovation, #loadbearing, #howtoframe, #howtoremoveawall, #howtoremovealoadbearingwall, #howtoremodel, #howto, #remodelingmyhouse, #dreamhouse, #openfloorconcept, #openfloor, #openfloorplan, #modernhome, #modernhouse

In this video I explain how to remove a load bearing wall in a home. One of the most common things homeowners want to do when buying a house, is remove a wall.. 9/10 times, it turns out to be a load bearing wall.

In this video, I explain in 9 easy to follow steps, how to remove a load bearing wall safely. Follow along as we take this wall out of a home a client of ours recently purchased!

#remodel #framing #construction

keywords: #ThisOldHouse, #DIY, #Construction, #HomeImprovement, #AskThisOldHouse, #Building, #TomSilva, #walls

Tom Silva explains what load bearing walls are, how to identify them, and what needs to be done in order to safely remove them.

SUBSCRIBE to This Old House:

-http://bit.ly/SubscribeThisOldHouse.

Tom Silva explains how to identify load bearing walls and how to remove them. Load bearing walls are an issue for many renovators today, as more homeowners are opting for an open concept layout instead of individual rooms. Unfortunately, these walls can’t be ripped out haphazardly as load bearing walls play a vital role to the structure of a house. They distribute weight from the roof, through the floors, and down to the foundation. Tom shares tips on how to determine if a wall is load bearing or not. He suggests going down to the basement or attic to see which way the joists run. If the wall is parallel to the joists, it’s probably not load bearing. If the wall is perpendicular, it’s most likely load bearing. Tom then demonstrates two ways of removing these walls, the above-ceiling technique and the below-ceiling technique. These methods will prevent the floor above from sagging and can give you the open layout you desire.

Cost: $1,000 – $10,000

Skill Level: Expert

Steps:

1. Determine whether a wall is load bearing or not. Check an unfinished basement or attic to see which way the joists run.

a. If the wall runs parallel to the joists, it’s probably not load bearing.

b. If it’s perpendicular, it most likely is a load bearing wall

2. Start by adding temporary walls to either side of the wall being removed to hold up the weight while work is being done. Place the temporary walls close enough to the structural wall but far enough away to work on the structural wall.

3. Remove the load bearing wall.

4. Add posts to either side of the wall to accept a beam to redistribute the weight above. Place them over the weight bearing beam in the floor below.

5. Use one of the techniques Tom demonstrated in the segment: the below-ceiling technique and the above-ceiling technique. Both methods rely on redistributing the weight from the load bearing wall to the walls beside it by creating point loads.

6. In the above-ceiling technique, cut into the joists to allow a beam to be installed in between. The joists will be attached to the new beam and the beam will rest directly on the point loads, but be flush with the ceiling.

7. In the below-ceiling technique, cut the posts slightly shorter and have the joists above rest directly on top of the beam across. The beam will be exposed, but it will keep the floor flush above.

8. Removing a load bearing wall by yourself can result in a lot of costly mistakes. It is best to consult a licensed engineer prior to beginning work on the project.

Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free:

-https://bit.ly/2GPiYbH

Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet:

-https://www.thisoldhouse.com/pages/streaming-app

About Ask This Old House TV:

From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment—your home.

Follow This Old House and Ask This Old House:

Facebook:

-http://bit.ly/ThisOldHouseFB

Twitter:

-http://bit.ly/AskTOHTwitter

Pinterest:

-http://bit.ly/ThisOldHousePinterest

Instagram:

-http://bit.ly/AskTOHIG

How to Identify and Remove a Load Bearing Wall | Ask This Old House

-https://www.youtube.com/user/thisoldhouse/

keywords:

See more articles in category: FAQS