Top 21 how to tell if a post is load bearing

Below is the best information and knowledge about how to tell if a post is load bearing compiled and compiled by the hkfindall.com team, along with other related topics such as:: how to tell if a wall is load bearing, load-bearing post, load bearing column removal, decorative load bearing post, non load bearing columns, can a hollow column be load bearing, load bearing column ideas, are hollow porch columns load bearing.

how to tell if a post is load bearing

Image for keyword: how to tell if a post is load bearing

The most popular articles about how to tell if a post is load bearing

7 Tips to Determine If a Column Is Load-Bearing or Decorative

  • Author: www.angi.com

  • Evaluate 4 ⭐ (25144 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about 7 Tips to Determine If a Column Is Load-Bearing or Decorative 2. Look for Visible Seams … One of the easiest visual cues to help you spot a load-bearing column are seams running lengthwise on opposite sides …

  • Match the search results: Try pulling the capital down from the top of the column. The capital is a separate piece, often with a decorative design, that sits on top of the column and directly bears the load above. If you can pull it away easily without much effort, it likely isn’t bearing much of a load.

  • Quote from the source:

How can you tell if a post is load bearing? – Cement Answers

  • Author: cementanswers.com

  • Evaluate 4 ⭐ (34546 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How can you tell if a post is load bearing? – Cement Answers How can you tell if a post is load bearing? Look for seams that run lengthwise on opposite sides of the column shaft. Oftentimes, a seemingly decorative …

  • Match the search results: How do you identify load-bearing beams? If a wall is marked as “S” in the blueprint, this means “structural,” thus showing it’s a load-bearing wall. Check your ceiling — Take a look at your ceiling to identify any load-bearing beams that run across the house. Any walls beneath these beams are …

  • Quote from the source:

How can you tell if a post is load bearing? – FindAnyAnswer.com

  • Author: findanyanswer.com

  • Evaluate 4 ⭐ (32250 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How can you tell if a post is load bearing? – FindAnyAnswer.com How can you tell if a post is load bearing? … Look for floor joists. If any of these joists meet a wall or a main support beam at a …

  • Match the search results: A load-bearing wall or bearing wall is a wall that is an active structural element of a building, that is, it bears the weight of the elements above wall, resting upon it by conducting its weight to a foundation structure. Load-bearing walls are one of the earliest forms of construction.

  • Quote from the source:

Decorative column or load-bearing? – Houzz

  • Author: www.houzz.com

  • Evaluate 4 ⭐ (37359 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Decorative column or load-bearing? – Houzz You may be able to visually verify that the columns ARE necessary by removing the drywall on and near the beams. If the beam ends at the column, it would …

  • Match the search results: At a first glance i am going to say it is not load bearing based the fact that it’s a 2×4 wall where as load bearing walls are 2×6. Also because a decorative post like that is not structurally sound to carry a weight load. But it’s always best to be 100% sure 😉

  • Quote from the source:

How to Tell the Difference between Load Bearing and …

  • Author: www.doityourself.com

  • Evaluate 4 ⭐ (34935 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Tell the Difference between Load Bearing and … Look for L-Brackets … One other clue that points to a load-bearing column is if you notice brackets that contribute to its support. Typically, L …

  • Match the search results: Identifying load-bearing porch columns can be a little bit more difficult than identifying load-bearing walls because you won’t have many exterior cues such as other walls or beams. Nevertheless, there are still some signs you can look for. As load-bearing porch columns are posts that help sup…

  • Quote from the source:

How to Identify and Remove a Load Bearing Wall – This Old …

  • Author: www.thisoldhouse.com

  • Evaluate 4 ⭐ (26097 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Identify and Remove a Load Bearing Wall – This Old … To determine if a wall is a load-bearing one, Tom suggests going down to the basement or attic to see which way the joists run. If the wall is parallel to …

  • Match the search results: To determine if a wall is a load-bearing one, Tom suggests going down to the basement or attic to see which way the joists run. If the wall is parallel to the joists, it’s probably not load-bearing. If the wall is perpendicular, it’s most likely load-bearing.

  • Quote from the source:

How to Tell if a Wall is Load Bearing – wikiHow

  • Author: www.wikihow.com

  • Evaluate 3 ⭐ (3558 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Tell if a Wall is Load Bearing – wikiHow Look for the signs of big, sturdy wooden or metal structures crossing a room’s ceiling and intersecting a wall that you know is load bearing or an external wall …

  • Match the search results: To tell if a wall is load bearing, examine the building’s blueprints to see where the original support beams were built. If you don’t have a copy of your blueprints, check your local county clerk’s office. Internal walls near the center of a building often help to support the weight of the house. Yo…

  • Quote from the source:

How to Tell If a Wall is Load Bearing – Mr. Handyman

  • Author: www.mrhandyman.com

  • Evaluate 3 ⭐ (8068 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Tell If a Wall is Load Bearing – Mr. Handyman Check your ceiling — Take a look at your ceiling to identify any load-bearing beams that run across the house. Any walls beneath these beams are …

  • Match the search results: Here is a checklist to tell if the wall you want to take down is load bearing:

  • Quote from the source:

How To Determine If A Wall Is Load Bearing [Update 2022]

  • Author: cbsmn.com

  • Evaluate 3 ⭐ (6328 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How To Determine If A Wall Is Load Bearing [Update 2022] You will need to look at the floor/ceiling joists. Notice how in the picture below the floor joists are running perpendicular to the wall. This could mean the …

  • Match the search results: However, if a structural engineer looked at that sketch (image 2) they would tell you, “it might be load bearing, but an onsite inspection to look at your attic, foundation, and your structure  is a must.”

  • Quote from the source:

How Can You Tell if a Wall is Load-Bearing? – Exact Structures

  • Author: www.exactstructures.co.uk

  • Evaluate 4 ⭐ (33677 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How Can You Tell if a Wall is Load-Bearing? – Exact Structures Load-bearing walls usually have posts, supports, or other walls directly above it. The small knee walls that support the roof rafters are also …

  • Match the search results: How to tell if a wall is load-bearing

  • Quote from the source:

Cost of Structural Engineer For Load Bearing Walls

  • Author: jacobmartin.com

  • Evaluate 4 ⭐ (37124 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Cost of Structural Engineer For Load Bearing Walls If you plan to add, move, or remove a load-bearing wall, structural engineers help … Finally, the engineer will tell if it would be good or bad for the …

  • Match the search results: Care should be exercised when moving a load-bearing wall as it is responsible for the building’s weight. With curtain walls, there is no need for many suggestions.

  • Quote from the source:

How do you Tell if a Wall is Load-bearing? – Synergy Design …

  • Author: www.renovatehappy.com

  • Evaluate 4 ⭐ (35934 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How do you Tell if a Wall is Load-bearing? – Synergy Design … In this case, the post seen in the ‘Before’ photo was load-bearing so a load-bearing beam was required when we removed it along with the knee- …

  • Match the search results: So, what are the telltale signs that might indicate if a wall is load-bearing or not?

  • Quote from the source:

How to Tell if a Wall or Column is Load-Bearing – Country …

  • Author: countryclubhomesinc.com

  • Evaluate 3 ⭐ (2253 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Tell if a Wall or Column is Load-Bearing – Country … How to Tell if a Wall or Column is Load-Bearing · Searching for beams at the lowest level of the house that interface directly with the concrete foundation.

  • Match the search results: Many homeowners seek to open up space in their home during a home renovation project by removing a wall. This can connect spaces and completely transform a home’s layout. Before a wall can be removed it must first be determined whether the wall is load-bearing. This can be determined by:

  • Quote from the source:

How to tell if a wall is load-bearing – The Living Room

  • Author: www.flyhomes.com

  • Evaluate 3 ⭐ (12334 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to tell if a wall is load-bearing – The Living Room How can I tell if a wall in the home is load-bearing? What if I can’t see the floor or ceiling joists? Can I remove a load-bearing wall? What …

  • Match the search results: If you can’t tell if a wall is load-bearing during the tour or if you’re already in the home, there are a couple of other strategies that will help you figure out whether a wall is load-bearing or not. 

  • Quote from the source:

How to Tell if a Wall is Load-Bearing | Our Expert Advice

  • Author: usihome.com

  • Evaluate 3 ⭐ (7061 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Tell if a Wall is Load-Bearing | Our Expert Advice During the construction of a house, load-bearing or non-load-bearing walls are made. Know how to identify them if you want to demolish one …

  • Match the search results: The first thing to do if you want to know if a wall is load-bearing is to gently tap its surface. If the wall sounds “hollow”, it is probably serving simply as a division and not as a structural element. Load-bearing walls tend to make a muffled sound when they are struck because the vib…

  • Quote from the source:

How to Identify a Load Bearing Wall – Dumpsters.com

  • Author: www.dumpsters.com

  • Evaluate 4 ⭐ (38068 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Identify a Load Bearing Wall – Dumpsters.com From using beams and joists to find your weight bearing walls to looking at blueprints, learn about four ways to determine if a wall is load …

  • Match the search results: “I would say find a structural engineer. They’ll be able to tell how additions or structural remodels may have changed how your home holds weight. If you can’t get a structural engineer, an architect or contractor would be up next.”

  • Quote from the source:

Column – load bearing or decorative? – DIY Chatroom

  • Author: www.diychatroom.com

  • Evaluate 3 ⭐ (14720 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Column – load bearing or decorative? – DIY Chatroom 1. column photo – if those are layers of ply, suggests it is decoration. Don’t know the specifics, but anecdotal logic says load bearing posts …

  • Match the search results: Another way to prevent getting this page in the future is to use Privacy Pass. You may need to download version 2.0 now from the Chrome Web Store.

  • Quote from the source:

How to Tell if a Wall is Load Bearing – Structural Engineering …

  • Author: structuralengineeringbasics.com

  • Evaluate 3 ⭐ (18422 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Tell if a Wall is Load Bearing – Structural Engineering … This post examines the common structural question of “how to tell if a wall is load bearing”. Structural Engineering Basics is a one stop …

  • Match the search results: A load-bearing wall is any wall that holds up the weight of the structure above and the people/furniture supported by that structure. The floors above, roof structure, people and furniture are the “loads” that the wall has to support. A load-bearing wall transfers load all the way down to the buildi…

  • Quote from the source:

How to Identify a Load Bearing Wall | Budget Dumpster

  • Author: www.budgetdumpster.com

  • Evaluate 3 ⭐ (11237 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Identify a Load Bearing Wall | Budget Dumpster Check the original blueprints. If you have blueprints of your home, there should be pages marked “S” for Structural. · Check for columns or posts …

  • Match the search results: A structural wall actually carries the weight of your house, from the roof and upper floors, all the way to the foundation. (The weight that is being transferred down at any given point in the house is called the “load,” hence “load-bearing walls.”) Because this weight is transferred from one level …

  • Quote from the source:

What To Know About Load-Bearing Walls – The Family …

  • Author: www.familyhandyman.com

  • Evaluate 3 ⭐ (11406 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What To Know About Load-Bearing Walls – The Family … Walls with a beam, column or jack posts directly underneath them are likely load-bearing. The wall is marked with an “S” on the blueprints. Load …

  • Match the search results: A load-bearing wall (AKA structural wall) supports the weight of the structures above it, such as the roof and the upper floors of multi-story homes. The weight of the structures they support is often referred to as the “load,” and load-bearing walls are designed to transfer the force of…

  • Quote from the source:

How to Repair a Load-Bearing Post – The Family Handyman

  • Author: www.familyhandyman.com

  • Evaluate 4 ⭐ (21615 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Repair a Load-Bearing Post – The Family Handyman Here’s what you need to know. Raising the main beam that carries the floors and interior walls of a house is complex. Don’t tackle it if you’re …

  • Match the search results: Join the support beam and wood load bearing post by toenailing them together and attaching two metal T-braces to opposite sides of the beam with galvanized 10d box nails. Once that’s done and the support strapping is reinstalled on all gas, electric, plumbing and heating lines, you’ll have the satis…

  • Quote from the source:

Multi-read content how to tell if a post is load bearing

How do I know if an item is loaded or not? Find the vertical seams on opposite sides of the column shaft. Typically, a decorative looking pillar or column is “split” in half to wrap and secure the two halves around a structure or bearing. It’s nearly impossible to hide these seams once they’re joined together.

How to define the bearing beams?If a wall is marked “S” in the plan, it means “structural”, indicating that it is a load-bearing wall. Check your ceiling – Take a look at your ceiling to identify load-bearing beams running through the house. All walls below these beams can be loaded.

How to differentiate load-bearing walls from non-load-bearing walls?If the beams in your basement or attic are directly touching the concrete floor and are perpendicular to it, chances are they are carrying a load. Non-bearing walls, on the other hand, are placed inside the house and do not support any structural weight of the building.

Can anyone tell me if the wall is load bearing?”If the upper wall is parallel or perpendicular to the struts, it is most likely carrying a load.” If you don’t have a basement — or if it’s finished — you can watch people scramble into your attic or crawl space, he says. They can also take fillers.

How do I know if an item is loaded or not? – Related issues

How do you know if a porch column is load-bearing?

In search of a visible organization

Since load-bearing porch posts are columns that help support weight, they must have a solid base. Note the area around the bottom of the porch column and see if there is any base type.

What size opening can you have in a load-bearing wall?

Any clearance of 6 feet or less can only have a 2×4 opening under the beam. This creates a fulcrum 1.5 inches wide. Any opening over 6 feet wide must have a minimum of two 2x4s under each end of the beam.

What happens if you remove a load-bearing wall?

Removing load-bearing walls can cause structural problems in a home, including sagging ceilings, non-beveled floors, cracked drywall, and sticking doors. Removing load-bearing walls without properly supporting the loads they carry can sometimes lead to structural collapse and even injury.

How do I know if it is a retaining wall?

The direction of the floor braces can indicate whether the wall is load-bearing – the load-bearing wall is usually perpendicular to the floor braces. You may see people shoving this floor from the basement looking up, or from the attic looking down on the floor below.

Find out how much a load-bearing wall costs?

Proper structural testing can determine if the wall is load-bearing. Structural inspections typically cost between $300 and $700, excluding planning. If a beam specification is required, it usually costs between $400 and $100 for each additional beam.

Do I need a structural engineer to remove a wall?

Load-bearing walls can be removed, but this is a complicated and expensive process that you need a structural engineer to oversee, so you should consult a professional before doing so.

Do I need an engineer to remove a bearing wall?

If you need to remove a load-bearing wall, we recommend hiring a structural engineer. An engineer will inspect the house, calculate the dimensions of the beams and columns you will need, and determine if you need additional shelves under the columns.

How much does front porch column replacement cost?

The cost of replacing patio posts will vary depending on the size required, the style you choose, and the material. On average, it will cost you between $316 and $455 to install new patio columns. Of course, if you choose a high-end column or something more ornate, your costs may be higher.

What type of wood is used to make porch columns?

Common woods for patio posts are mahogany, poplar, cherry, pine, oak, maple, and redwood. If you plan to paint the columns, pine or cedar will be better than some of the other options.

Can a column rest on a beam?

Normally, the column rests on the foundation to transmit the load from the slabs and beams. But the floating column rests on the beam. This means that the column support beam acts as a foundation. This beam of light is called the transmitted beam.

Can a door withstand a force?

Exterior walls are almost always load-bearing. In places with windows and doors, the walls consist of beams or ends that extend beyond the top of the openings. The posts on either side of the opening support the beams. A house will rarely have an entire non-loadbearing exterior wall.

Can I cut a gap in a bearing wall?

Steps to cut a passage in a load-bearing wall

Drive the studs into the temporary wall until they are snug. Use the drill/driver to attach the brace to the uprights. Use a level to trace the outline of the opening. Drill holes with a jigsaw.

Can you remove part of the bearing wall?

Is it possible to remove a bearing wall? Sure. Although some people may tell you that you can knock down a load-bearing wall yourself, this is by no means a do-it-yourself project. Arbitrarily removing a load-bearing wall can lead to all sorts of costly mistakes, which can significantly damage the structure of your home.

How do you know if an interior wall is load-bearing?

To determine if a wall is a load-bearing wall, Tom suggests going down to the basement or attic to see how the railings work. If the wall is parallel to the struts, it cannot be loaded. If the wall is perpendicular, chances are the wall is under load.

How much does it cost to remove the bearing wall and install the beams?

Removing a non-load-bearing wall in a home costs on average between $500 and $2,000. Replacing a bearing wall with a bearing beam costs $4,000 to $10,000. Hiring a structural engineer to calculate load-bearing wall removal costs between $300 and $1,000.

How long can a bearing beam be?

Standard 2 x 12 beams on 16 inch centers are used to stretch 15 feet. The theoretical dimensions of a bearing beam needed to support a particular weight are easy to calculate, but the actual choice of beam depends on considering the factors of the particular situation.

Do all houses have load-bearing walls?

Reality: Usually, all exterior walls of a house are load-bearing, but not guaranteed. Many people assume that all exterior walls are load-bearing and weather-resistant. It’s not always the case. It depends on where the bracing and truss support the floor, which varies by house type and style.

Are the interior walls load-bearing?

A load-bearing wall is a wall that supports the weight of the stories above it. Classified as an active element, they provide structural integrity by guiding this weight to the base of the building. Exterior walls are almost always as load-bearing as some interior walls, although this is where problems tend to arise.

Can I remove the wall under the stairs?

As long as you don’t think about getting rid of it, just the triangular part, you should be fine. The middle right portion of the stair is almost always freestanding, hence why you may want to remove the buttress, as this is where anchoring the top and bottom sections of the stair is important.

How much does interior wall removal cost?

How much does it cost to remove the wall? Removing a wall in your home usually costs between $300 and $1,000 if it is a non load bearing wall. In contrast, removing a load-bearing wall costs between $1,200 and $3,000 for a one-story home. Prices range from $3,200 to $10,000 for homes with more than one story.

How much does a structural engineer cost?

Structural engineering plans cost an average of $800 to $3,000. They charge between $100 and $200 per hour. For new construction or major renovations, 1% to 20% of the total construction cost, or $1,500 to $20,000, goes to the structural engineer. Structural engineers often invoice using a combination of methods.

Popular questions about how to tell if a post is load bearing

Video tutorials about how to tell if a post is load bearing

keywords: #loadbearingwall, #loadbearingwallvsnonloadbearingwall, #removeawallinahouse, #supportingwalls, #supportingwallremoval, #supportingwallornot, #supportingwallinahouse, #supportingwallhowtotell, #supportingwallbeam, #supportingaloadbearingwallwithabeam, #loadbearingwallremoval, #loadbearingbeaminstallation, #loadbearing, #howtotellifawallisloadbearing, #ismywallloadbearing, #howtoknowifawallisloadbearing, #removeloadbearingwall

Want More Luxury Home Design ideas? Check out Luxury homes we build at

-https://emmettleohomes.com/gallery/

This Video gives you the gives you the FASTEST and EASIEST ways to tell if a wall in your home is load bearing or not. This answers the questions,, CAN YOU TAKE IT OUT, OR NOT. Please always consult with a professional engineer prior to removing any wall in your home that you are not POSITIVE is a bearing or supporting wall.

▶ Check out my gear on Kit:

-https://kit.com/DanielNagy

Planning on building or renovating? Get your free LUXURY HOME PLANNING GUIDE at Emmettleohomes.com

Emmett Leo Homes is a luxury custom home builder in Winnipeg, Mb. Come with us on a fun journey of building, and renovating custom luxury homes. From multi-million dollar home builds, to massive luxury flips, Emmett Leo Homes is giving you an insiders look into the world of luxury homes, offering tips, tricks, insider looks and inspiring ideas.

-https://EmmettLeoHomes.com

Dan Nagy is the founder of Emmett Leo Homes, entrepreneur, investor, and a retired City Firefighter. After a catastrophic, near career-ending injury, Dan focused his energy into creating the most exclusive luxury building company, using all of his experience in building and renovating profitable luxury spec homes. Learn more about Dan in the link below.

-https://emmettleohomes.com/about-us/

Follow Dan and Emmett Leo Homes at:

Pinterest:

-https://www.pinterest.ca/EmmettLeoHomes/

Houzz:

-https://www.houzz.com/pro/webuser-872

Instagram:

-https://www.instagram.com/emmett.leo.homes

Twitter:

-https://twitter.com/Emmettleohomes

Facebook:

-https://www.facebook.com/Emmett.Leo.Homes

Website:

-https://EmmettLeoHomes.com

A load bearing wall means that it is holding the weight of any structure around or above it.

A non-load bearing wall means its not, and its simply there to divide the space.

The quickest way to tell if a wall is load bearing or not is to find out which way the joists above it run. If they run at a 90 degree angle, and your wall is close to the middle of the house, chances are you may be looking at a load bearing wall.

Can’t figure out which way the joists run? Looking at a room, and seeing which is the shortest direction from the outside wall to the middle of the house can also indicate which way they run.

The third easy way is to check is to see if you have a gable roof. If you have a gable roof, which means that one two sides of the roof do NOT have eaves troughs, and the wall runs all the way to a point, then you can easily determine which way the roof trusses run. A quick rule of thumb is that the roof trusses will generally run the same direction as the floor joists. That lets you know that the main beam, and any structural wall will probably run the opposite way.

If none of those quick ways work, you may have to first understand a little more about structural support and why your home is the way it is.

First thing we have to do is understand that the structure of a house is always supported from foundation up. This means that in the ground, there is always some sort of supporting foundation

Typically, there will be concrete piles, or a footing that holds yours basement foundation walls from sinking.

In a typical home, you will have a beam that runs in the middle of the foundation from on side to the other, that will support your floor joists. Then you will have one or a few posts that support underneath the beam.

Moving up to the first floor, you may have to bring that supporting ability up to a second floor, or if in a bungalow, into the roof system. A typical house will have a supporting wall almost directly above the basement beam.

Go to the basement and check to see if you can find any open supporting structures

These include Posts that are in the middle of the basement, or open beams that space across the middle of the home. Beam can be made out of different material, including, wood, LVL, or even steel. Newer homes hide them well, unless the basement is unfinished. Do you have a drop ceiling anywhere?

It’s important to know which way the joists run above every level, because they may NOT always run the same way in the basement, as they in the first or second floors.

We have found our beam, as we don’t generally have supporting interior walls in the basement, and that typically means that there will be a supporting wall directly above or close on the floor above.

You will see a wall supporting perpendicular joists. Perpendicular simply means they run at a 90 degree angle across. That allows the wall to support they weight of the floor system.

1)Here are some other ways to find the joists in your ceiling.

you may need to use a stud finder

2)see if you can find multiple drywall screws that will show you where your joists are

3)cut into the ceiling and check.

4)There is also an option to find the old building plans.

keywords: #ThisOldHouse, #DIY, #Construction, #HomeImprovement, #AskThisOldHouse, #Building, #TomSilva, #walls

Tom Silva explains what load bearing walls are, how to identify them, and what needs to be done in order to safely remove them.

SUBSCRIBE to This Old House:

-http://bit.ly/SubscribeThisOldHouse.

Tom Silva explains how to identify load bearing walls and how to remove them. Load bearing walls are an issue for many renovators today, as more homeowners are opting for an open concept layout instead of individual rooms. Unfortunately, these walls can’t be ripped out haphazardly as load bearing walls play a vital role to the structure of a house. They distribute weight from the roof, through the floors, and down to the foundation. Tom shares tips on how to determine if a wall is load bearing or not. He suggests going down to the basement or attic to see which way the joists run. If the wall is parallel to the joists, it’s probably not load bearing. If the wall is perpendicular, it’s most likely load bearing. Tom then demonstrates two ways of removing these walls, the above-ceiling technique and the below-ceiling technique. These methods will prevent the floor above from sagging and can give you the open layout you desire.

Cost: $1,000 – $10,000

Skill Level: Expert

Steps:

1. Determine whether a wall is load bearing or not. Check an unfinished basement or attic to see which way the joists run.

a. If the wall runs parallel to the joists, it’s probably not load bearing.

b. If it’s perpendicular, it most likely is a load bearing wall

2. Start by adding temporary walls to either side of the wall being removed to hold up the weight while work is being done. Place the temporary walls close enough to the structural wall but far enough away to work on the structural wall.

3. Remove the load bearing wall.

4. Add posts to either side of the wall to accept a beam to redistribute the weight above. Place them over the weight bearing beam in the floor below.

5. Use one of the techniques Tom demonstrated in the segment: the below-ceiling technique and the above-ceiling technique. Both methods rely on redistributing the weight from the load bearing wall to the walls beside it by creating point loads.

6. In the above-ceiling technique, cut into the joists to allow a beam to be installed in between. The joists will be attached to the new beam and the beam will rest directly on the point loads, but be flush with the ceiling.

7. In the below-ceiling technique, cut the posts slightly shorter and have the joists above rest directly on top of the beam across. The beam will be exposed, but it will keep the floor flush above.

8. Removing a load bearing wall by yourself can result in a lot of costly mistakes. It is best to consult a licensed engineer prior to beginning work on the project.

Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free:

-https://bit.ly/2GPiYbH

Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet:

-https://www.thisoldhouse.com/pages/streaming-app

About Ask This Old House TV:

From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment—your home.

Follow This Old House and Ask This Old House:

Facebook:

-http://bit.ly/ThisOldHouseFB

Twitter:

-http://bit.ly/AskTOHTwitter

Pinterest:

-http://bit.ly/ThisOldHousePinterest

Instagram:

-http://bit.ly/AskTOHIG

How to Identify and Remove a Load Bearing Wall | Ask This Old House

-https://www.youtube.com/user/thisoldhouse/

keywords: #Load-bearingWall, #How-to(MediaGenre), #wall, #load, #bearing, #non, #interior, #house, #home, #reno, #renovation, #demo, #remove, #take, #down, #InteriorDesign(ProjectRole), #removal, #structural, #structure, #Construction, #Repair, #Installation, #Out, #identify, #tell, #how-to, #how, #to, #tips, #upgrade, #improve, #improvement, #truss, #joist, #engineer

If you want to help support Shannon to produce more videos like this, visit

-https://www.house-improvements.com/donate

Shannon from

-https://www.house-improvements.com

Videos produced by SKS Media (House-Improvements.com) are provided for informational purposes only. The information contained in the videos is intended to give general guidance to simplify DIY (do it yourself) projects. Because tools, products, materials, equipment, techniques, building codes and local regulations are constantly changing, SKS Media cannot and does not assume any responsibility or liability for the accuracy of the information contained therein. Further, SKS Media will not accept any claim for liability related to, but not limited to, omissions, errors, injury, damage or the outcome of any project. It is the responsibility of the viewer to ensure compliance with all applicable laws, rules, codes and regulations for a project. The viewer must always take proper safety precautions and exercise caution when taking on any project. If there are any questions or doubt in regards to the element of a project, please consult with a licensed professional. SKS Media conducts all matters in accordance with the laws of Saskatchewan, Canada.

keywords: #howtotellifawallisloadbearing, #loadbearingwall, #supportingwall, #howtotellifawallissupporting, #supportingbeam, #loadbearingbeam, #diy, #doityourself

In this video, I show you how to tell if a wall is load-bearing! There are a few things that you can do to determine whether or not a wall is load-bearing; however, I outline one of the easiest methods! All that you have to do is look on top of the wall and see if it is supporting anything above it. If it isn’t supporting anything, then is is LIKELY not a load-bearing wall. If it is supporting joists from the floor above or roof supports, then it is LIKELY a load-bearing wall. I show you a load-bearing beam in my basement, and use it as an example to explain the process.

CONNECT WITH ME:

Instagram –

-https://www.instagram.com/mikechimmy/

SUBSCRIBE TO MY CHANNEL:

-https://youtube.com/subscription_center?add_user=helpfuldiy

FREE DIY ADVICE EBOOK:

-https://gumroad.com/l/vFujc

Disclaimer: Some of the links in this description may be affiliate links. All opinions are my own.

See more articles in category: FAQS

Maybe you are interested

Sale off:

Best post:

Categories