Best 18 what is a flush beam

Below is the best information and knowledge about what is a flush beam compiled and compiled by the hkfindall.com team, along with other related topics such as:: drop beam vs flush beam, flush beam deck, dropped beam, flush beam hanger, lvl flush beam, install flush beam, flush steel beam, flush beam cost.

what is a flush beam

Image for keyword: what is a flush beam

The most popular articles about what is a flush beam

What does a flush beam mean? – AskingLot.com

  • Author: askinglot.com

  • Evaluate 3 ⭐ (18436 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What does a flush beam mean? – AskingLot.com A flush beam, also known as a header beam, is a structural component that is located at the same level of ceiling joists and one that …

  • Match the search results: A drywall cover makes the beam virtually disappear into the ceiling, making it look more like a soffit than a beam. Secure the drywall directly to the beam, tape and cover all the nails and corners. Add texture with drywall mud to match the ceilings and walls. When dry, paint the beam to match the …

  • Quote from the source:

What is a flush beam on a deck? – AskingLot.com

  • Author: askinglot.com

  • Evaluate 3 ⭐ (6358 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What is a flush beam on a deck? – AskingLot.com A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you …

  • Match the search results: Upset Beam — This is a type of flush beam used when supporting an upper wall or structural element where the beam extends above the upper floor surface. Used in line with walls, or in attics.

  • Quote from the source:

Replacing a Load-Bearing Beam With A Flush Beam – A …

  • Author: www.aconcordcarpenter.com

  • Evaluate 4 ⭐ (36556 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Replacing a Load-Bearing Beam With A Flush Beam – A … Have an engineer specify a steel beam to fit inside the ceiling joist area. If there is unfinished attic space above, install the beam flush …

  • Match the search results: So we turned to a local steel company that supplies, preps and installs the beam. We supplied the steel company with the length of beam which was the entire beam length minus ¼” and specified that we wanted the beam to fit inside a 2×10 joist bay. The steel company uses a local structural engin…

  • Quote from the source:

What is a flush header? | EveryThingWhat.com

  • Author: everythingwhat.com

  • Evaluate 3 ⭐ (9806 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What is a flush header? | EveryThingWhat.com A flush beam, also known as a header beam, is a structural component that is located at the same level of ceiling joists and one that …

  • Match the search results: A flush beam, also known as a header beam, is a structural component that is located at the same level of ceiling joists and one that utilizes joist hangers for attachment. It is often used for framing deck forms like octagons, or for stair landings where a cantilevered beam is not the most sensible…

  • Quote from the source:

How to Install a Deck Flush Beam vs. Drop Beam | Trex

  • Author: www.trex.com

  • Evaluate 3 ⭐ (14997 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Install a Deck Flush Beam vs. Drop Beam | Trex Learn the difference between flush and drop beams to determine which one is right for your project.

  • Match the search results: Mounting the beam in a notch of the support post is another method.  This is usually done on the drop beam scenario and not on the flush beam. If this notch were done on the flush beam, the joist could come into the support post and not be able to attach to the beam. The notch is used to keep the be…

  • Quote from the source:

What does a flush beam mean? – NCERT Point

  • Author: www.ncertpoint.com

  • Evaluate 4 ⭐ (30949 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about What does a flush beam mean? – NCERT Point Answer. In construction, a flush beam, also known as a header beam, is a structural component that is situated at or near the same level as …

  • Match the search results: The section modulus is calculated using the formula: beam width times beam depth squared divided by 6. Because the actual dimensions of a two-by-6 standard beam are 1.5-by-5.5 inches, the section modulus of the beam would be 1.5-by-5.5 = 7.6 (1.5 x 5.5 x 5.5 / 6 = 7.6), which is insufficient for thi…

  • Quote from the source:

What Does A Flush Beam Mean? – Whoat Where Why

  • Author: whoatwherewhy.com

  • Evaluate 3 ⭐ (13853 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What Does A Flush Beam Mean? – Whoat Where Why A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you …

  • Match the search results: The Inverted beam is a reinforced concrete beam, different types shape of beam-like I beam, T Beam, L beam, etc. … Inverted beams are popular and form an essential part of modern reinforced concrete framed structures. Lastly, strict and rigid architectural considerations led to the provision of inve…

  • Quote from the source:

What is a flush beam deck? – Roadlesstraveledstore

  • Author: www.roadlesstraveledstore.com

  • Evaluate 3 ⭐ (17681 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about What is a flush beam deck? – Roadlesstraveledstore A flush or header beam is a structural member positioned at the same level as the … Flush beams are commonly used for framing angled deck forms such as …

  • Match the search results: The beam span for most deck beams is less then 16 feet (4.87 meters) but can be as small as 8 feet (4.87 meters) depending on the thickness of the beam. These special beams support the weight of the main floor on the deck are an essential for overall structural integrity.

  • Quote from the source:

Flush Beam or Header – MSI Home Improvements & Repairs

  • Author: www.mindsetsolutions.ca

  • Evaluate 4 ⭐ (33724 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Flush Beam or Header – MSI Home Improvements & Repairs Flush beams are meant to be hidden in a attic or upper floor joist frame. The term flush is referred to the finished ceiling that is now even in both rooms …

  • Match the search results: Depending on the renovation project, engineering and span the type of beam to be used is a important part of any open concept design. Many factors come into play determining the right type of beam to be used. Such as the span, weight loads, design and look. Most beams are replacing a space wher…

  • Quote from the source:

Flush-Framed Floor Joists | JLC Online

  • Author: www.jlconline.com

  • Evaluate 4 ⭐ (24497 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Flush-Framed Floor Joists | JLC Online But if dimensional lumber is hung flush from a beam made of steel or engineered lumber, the result can be a bulge at the beam, as shown below. When installing …

  • Match the search results: Using flush beams with hangers, or engineered lumber or steel, can reduce the potential for shrinkage problems. But if dimensional lumber is hung flush from a beam made of steel or engineered lumber, the result can be a bulge at the beam, as shown below.

  • Quote from the source:

Member Types – ForteWEB

  • Author: www.forteweb.com

  • Evaluate 4 ⭐ (31048 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Member Types – ForteWEB Flush Beam: The alignment of the top of a horizontal member with the top of the joists and other flush beams; generally, bearing occurs with the use of …

  • Match the search results: Flush beam: a roof load carrying member whose top is aligned with the top of roof joists and other flush beams which usually attach to it through the use of hangers.

  • Quote from the source:

Sizing a Beam – Trus Joist Technical Support

  • Author: www.techsupport.weyerhaeuser.com

  • Evaluate 3 ⭐ (12718 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Sizing a Beam – Trus Joist Technical Support Pressure Treated – wood that has been infused with chemical preservatives to protect the wood from rot. · Flush Beam – a beam that will be in the same elevation …

  • Match the search results:
    RayID: 6fa12b5f080889b2

    IP: 103.116.106.97

  • Quote from the source:

structural ridge vs flush beam vs scisso – Fine Homebuilding

  • Author: www.finehomebuilding.com

  • Evaluate 4 ⭐ (34069 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about structural ridge vs flush beam vs scisso – Fine Homebuilding 2×6 ceiling joists are 12′ long and overlapping on the bearing wall. Everyiting is 16″ o.c.. The lumber yard told me I could put in a flush beam …

  • Match the search results: OK, sorry for any confusion. #1) I’ll look into 2 larger LVL’s rather than 3 smaller ones for a flush beam as Bosshog suggested. This also means that the in the wall end supports would only have to be 3 1/2 inches wide to support the flush beam. #2) Framer, I read that piece you reference…

  • Quote from the source:

Part II of III “Items commonly shown on Shane Homes Main …

  • Author: www.shanehomes.com

  • Evaluate 4 ⭐ (27310 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Part II of III “Items commonly shown on Shane Homes Main … So, even though a flush beam will give you a nice flat ceiling, it will mean that we will have to route the heating and plumbing through another …

  • Match the search results: Where joists need support, but are too far away from a supporting wall, that’s where we will use a beam. There are 3 different positions to place a beam in a floor system.
    o A dropped beam is what is most common, and most economical. The floor joists will sit on top of the beam, and the beam …

  • Quote from the source:

Opening Up A Bearing Wall | Northwoods Lumber Co.

  • Author: northwoodslumber.com

  • Evaluate 3 ⭐ (15107 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Opening Up A Bearing Wall | Northwoods Lumber Co. Because a flush beam sits above the ceiling plane, it would have provided the maximum headroom. But retrofitting a flush beam would have required removing a …

  • Match the search results: Header strategies. To support the wider opening, I would need a longer header beam to replace the existing one. In these cases, there are two options for a new header beam: a carrying beam that supports the floor joists from below, or a flush beam that attaches to the ends of the joists via joist ha…

  • Quote from the source:

Flush beam vs drop beam? : r/Decks – Reddit

  • Author: www.reddit.com

  • Evaluate 4 ⭐ (22891 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Flush beam vs drop beam? : r/Decks – Reddit Flush beam is a little cheaper, because you still need the outer band, hangers, etc, but now you are just doubling it up. With the drop beam …

  • Match the search results: A drop beam and a flush beam will cost exactly the same minus a few joist hangers needed for the flush beam. I much prefer the look of a flush beam as well. Other than that, both can be used so go with what you like better!

  • Quote from the source:

Flush beam deck – Home Improvement Forum

  • Author: www.house-improvements.com

  • Evaluate 4 ⭐ (22508 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Flush beam deck – Home Improvement Forum Hence, the joists will need to be hung from the beams and flush. – The beams will need to run perpendicular to the house (joists parallel) …

  • Match the search results:

    Post

    by A. Spruce » Thu Jun 06, 2019 10:55 am

  • Quote from the source:

How to Install Deck Header & Flush Beams

  • Author: decksdotcom.azurewebsites.net

  • Evaluate 4 ⭐ (25658 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Install Deck Header & Flush Beams A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you would at the …

  • Match the search results: A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you would at the ledger board.  Flush beams are commonly used for framing angled deck forms such as octagons or on stair landings where a cantilevered beam…

  • Quote from the source:

Multi-read content what is a flush beam

Replacing a loaded beam with a flush beam

Going throughRobert RobillardaboveHome repair and renovation

Tweeter

Eliminate load-bearing walls or exposed beams

Replacing a bearing beam with a flat beam was our task last week. The client already had a wooden beam with two posts connected to his kitchen island and did not want to see the slats.

The decision was made to install a beam that would span the entire kitchen without posts and would be recessed into the ceiling.

Decision: hide or overwhelm the beam

Depending on the situation, application, beam size and budget, there are options. Although this is NOT always the case, many replacement LVL beams are deeper than “older” ceiling beams and cannot be hidden.

Selection beam

In this situation, you have several options:

  1. Install beams under the ceiling
  2. Tunnel a larger beam into the ceiling space and leave part of the beam protruding lower than the ceiling.
  3. Have the engineer specify a steel beam for mounting inside the ceiling beam area.
  4. If there is an unfinished attic above, install cross beams with beams sticking out into the unfinished space.

Steel Beam Engineering

We first started working with our sawmill who specified the LVL beam.

Our problem is that the LVL demand duration is MUCH deeper than the ground duration. When recessed, the LVL beam will project 8 to 10 inches below the ceiling.

So we turned to a local steel company to supply, prepare and install the beams. We provided the steel company with a beam length equal to the overall length of the beam minus ¼” and specified that we wanted the beam to fit into a 2×10 beam cavity. The steel company employed a local structural engineer, who specified W8x58 steel beams with 4×6 PSL piles. PSL piles transfer the weight to other piles [bearing points] or foundations below.

To note- with steel beams, the engineer can specify 4×6 PSL posts fixed with metal connectors, or steel posts welded to steel plates.

contact bolts

We provided the steel company with a floor beam layout, so they could drill 1/2″ holes between the floor beams. The holes allow the hardwood to be bolted to the beams. Bolts or threaded rods can be used to attach the wood to the beams.

POINT:Threaded rods are more affordable and easy to find.

Beam preparation

Solid wood was installed on each side of the beams. This is called “beam wrapping”, three 2×8 boards are needed to span through the top and bottom steel flanges. This solid wood allows the panels to be fixed via hooks.

POINT:When installing wooden blocks; the area where the top and bottom flanges contact the vertical array of I-beams is slightly rounded. Bend the edges of your 2×8 to fit the canvas.

Preparation

Prior toremove a load-bearing wall, remove the panel from the wall or ceiling to reveal the frame. Then, remove or relocate any conductors, pipes, or conduits in the path of the harness.

Strip the ceiling 2 to 3 feet behind the wall to be removed or beamed, and install your temporary wall. This is needed to access ceiling frames, move electrical wiring, piping, and install your temporary retaining walls.

In our case, we built the wall 4ft due to the kitchen island and needed a 4ft hallway for the Sumner Roust-A-Bout lift to roll. The beam was heavier than one lift could support, so two lifts were used. 48″ clearance is required just below and above each end of the beam. In some cases, a lift is enough and this lift will be concentrated under the beam.

POINT:Before you build your temporary walls, talk to the Steelsmith and see what he needs to clean up his gear.

temporary retaining wall

Attach temporary wall studs to the top and bottom panels, 2 to 3 feet from the wall or beam. Ensure a snug fit by cutting dowels about 1⁄8 to 1⁄4 inches long and driving them into place. Place studs under each ceiling brace and use two or three 3-inch bars

The temporary stud loading will occur when you remove the bearing wall or beam. In our case, we noticed the load after removing two vertical posts.

Tip: Install mid-height horizontal or diagonal braces on temporary walls to prevent studs from bending.

Do you need a temporary wall underneath?

With only the floor load and the attic above to support, I felt that 4 foot drum reach wouldn’t be a problem. But in more complex cases where there is a ridge or other heavy load above, I always consult an engineer who specifies the proper spacing, connectors, and removal sequences. .

REMARK- If there is a load bearing wall above the one you wish to remove, you will need a second pair of load bearing walls directly above the first pair. Otherwise, the upper load-bearing wall will only be supported by the floor when you cut out sections of the bracing below.

Ceiling cut joist “Beam pocket”

We removed a beam and replaced it with a flat beam, so we used the same beam recess locations, but enlarged them to accommodate the new steel beam.

To note:When cutting your beam bags, add 1/2″ to the steel beam width measurement to allow for easier installation.

We used a Bosch Blue series laser to connect the two beam pocket positions, then used a speed square to mark the cuts directly on the braces. To start each cut, a circular saw was used and ended with a moving saw.

After cutting the cluster bag, remove any loose nails to make room for the beam. We use nail clippers to cut the nails or a mobile saw to cut them.

To note: Any stray nails can be driven into the subfloor or finished floor once the beams are installed.

Install the harness

When the package bag was prepared, we rolled twoSumner Roust-A-Bout. Liftinto position and center them under the beam. Then the beam was lifted and in the correct position.

The Sumner Roust-A-Bout Elevator allows one person to lift and place orders in tight areas that cannot be accommodated by other elevators. An elevator can lift a 1,500 lb load to a maximum height of 25 feet in minutes.

Beam Support Post Parameters – Load Points

Next, 4×6 PSL engineered pillars were installed under each beam end.

Point:Cut the posts 1/8″ long, then angle them gently into place by tilting the bottom of the posts into place, then driving the ends along the surface of the beam. It would not take much force to put them in place, if they were re-measured and corrected.

The 1/4″ steel L-rack is then attached to the PSL posts with Headlock structural screws, then the bracket is welded to the beam.

If possible, add and attach PSL studs to the wall bracket installed on both sides of the top and bottom panels.

When a load-bearing beam is replaced by a flat beam, the bearing points of the new beam must transfer all the weight to the foundation, which means that the engineer may need additional support on the floors under the load-bearing posts. . It’s also making sure there’s a solid block between the floor and the rim.

To note- Sometimes you may need to add or expand the base of the footing under the support columns to accommodate the additional point loads created by your new creation.

Install joist hangers

Before installing the beam supports, we use a hydraulic floor to lift the low beams to the bottom of the beams.

2 × 10 hangers with cross holes to “halve the nails”. This locks the beam to the beam and the drawers pop out. A longer lanyard is required for double cut nailing. We use a 16D sink or Simpson Strong-Tie®Hard disk®SD connector screws.

Note – Fill all holes in the ledger hanger lanyard.

Completed project

Once the beam is in and inspected, it’s time to close the ceiling and refinish the room. Replacing a bearing beam with a flush beam opened up this room – no posts yet!

Installation of a steel beam

If you liked this article, be suresubscribe to my RSS feed!

Learn more about home repair and renovation

  • How to Fasten Pile Strips to Concrete
  • How to Repair Lawn Irrigation Hose
  • 20 considerations to ensure the smooth running of the project
  • Floor reinforcement joists
  • Repair copper lanterns

Popular questions about what is a flush beam

what is a flush beam?

A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you would at the ledger board. Flush beams are commonly used for framing angled deck forms such as octagons or on stair landings where a cantilevered beam would be less practical.

What is the difference between a flush beam and drop beam?

Flush Beam: The alignment of the top of a horizontal member with the top of the joists and other flush beams; generally, bearing occurs with the use of hangers. Drop Beam: The alignment of the bottom of joists, flush beams, and other framing components with the top of a beam.

How do you install a flush beam?

What is one advantage to using a flush beam in a floor system instead of a drop beam?

A flush beam is good at simplifying and making installation easier for heating, plumbing and electrical systems. A flush beam enables faster installation for these processes. It is also a good idea to check out hardware stores in your area such as Home Depot and Lowes.

How do you frame a beam deck flush?

What does flush mean in framing?

A flush or header beam is a structural member positioned at the same level as the joists and uses joist hangers for attachment just as you would at the ledger board. Flush beams are commonly used for framing angled deck forms such as octagons or on stair landings where a cantilevered beam would be less practical.

What are the types of beam?

Types of beam structure
  • Continuous beams. A continuous beam is one that has two or more supports that reinforce the beam. …
  • Simply supported beams. Simply supported beams are those that have supports at both end of the beam. …
  • Fixed beams. …
  • Overhanging beams. …
  • Cantilever beam.

How much does it cost to put a load-bearing beam in?

Load-Bearing Support Beam Cost

A load-bearing support beam costs between $3 and $35 per linear foot, with most homeowners spending $10 to $15 per linear foot. A laminated veneer lumber (LVL) beam costs $60 to $300 on average without installation. *Prices are for materials only.

How much does it cost to fit an RSJ UK?

How much do RSJs cost?
Steel RSJ costs Cost + VAT (Range low – high) Average cost
RSJ beam cost 1m – 5m (up to 46kg per m) £200 – £950 £575
RSJ installation up to 46kg per m (1-5m) £300 – £750 £500
RSJ cost per metre (per kg) £2.50 – £4.50 per kg £3.50 per kg

Can you replace a load-bearing wall with a beam?

When you or a contractor remove a load-bearing wall, it must be replaced with either a structural beam or a structural beam and post or posts.

Do floor joists have to sit on a beam?

Floor joists spread the loads bearing from above, and must be framed adequately to complete the load paths. Ideally, if a load-bearing wall runs parallel to floor joists, then it should sit directly over a beam or a joist supported by a load-bearing wall below.

How far can you cantilever a LVL?

The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.

Can you hang joists from a beam?

Joist hangers are safe if installed correctly. Hanging joists is by no means new. You typically need to hang a joist if the top of it needs to be in the same plane as the beam that supports it. There are all sorts of reasons and conditions on jobs where this is necessary.

Can a 6×6 be used as a beam?

The distance a 6×6 can span as a beam depends on the species of wood, grade, grain orientation, moisture content or seasoning, condition, and load. Southern Pine (SP) 6x6s will span 5” to 8” further than other common softwood species of the same grade.

Can you cantilever a flush beam deck?

Re: Flush beam deck

With the layout in your drawing, you don’t have to be any closer than about 6″ with the beams/joists because the decking itself can be cantilevered the remaining distance without any problem (assuming lumber and not Trex-like material).

Video tutorials about what is a flush beam

keywords: #chiasẻ, #điệnthoạicómáyảnh, #điệnthoạiquayvideo, #miễnphí, #tảilên

What Is a Flush Beam?. Part of the series: Home Improvement \u0026 Remodeling. A flush beam is a header beam that lies flush against ceiling beams, and it is held in place by joist hangers. Discover how a flush beam can be used to make the installation of duct work easier with help from a professional carpenter in this free video on home improvement and ceiling beams.

keywords: #howtoremoveadropbeam, #howtoreplaceadropbeam, #Buildingaflushbeam, #howtobuildaflushbeam, #usingahangernailer, #howtorenovatealivingroomonabudget, #howtorenovatealivingroom, #renovatinganoldhouse, #ideasforrenovatinganoldhouse, #openfloorplan, #loadbearingwall, #loadbearingwallbeam, #openfloorplanremodel, #uptokode, #kodyhorvey

Watch as we remove a drop beam and replace it with a flush mount beam to open up an old living room and kitchen. We will walk you through all the steps you need to do and we will show you the benefits of using a hanger nailer from Prime Fasteners.

**************************************

I’m Kody Horvey, owner of Up To Kode; a full service carpentry, contracting and consulting company that proudly serves Red Deer and all of Central Alberta.

We are committed to being Central Alberta’s most sustainable and energy efficient builder with a strong focus on quality and innovation.

Our vision is to continually implement and increase the use of high efficient building practices and products to create sustainable, multi generation structures.

Here on YouTube, we hope to share our work, get you inspired, and give you the knowledge to plan and execute your own projects.

Questions? Just ask! Email [email protected]

➤What to Watch Next:

IKEA Kitchen Cabinet Course: (

-https://www.youtube.com/watch?v=IjdCYsr9Jns\u0026list=PLh04OCfZ3jzzx9keR2Kqx5MiwFHetXxXh)

ICF 101: (

-https://www.youtube.com/watch?v=h_bxdq0hIW4\u0026list=PLh04OCfZ3jzz76xWspyhowJuaxjfpPRnK)

Drywall for Beginners: (

-https://www.youtube.com/watch?v=0I0WFiEtVyI\u0026list=PLh04OCfZ3jzyWptXqOCE5h2AgXv2GlMFi)

Advanced Drywall Course: (

-https://www.youtube.com/watch?v=RycwYGJWaEE\u0026list=PLh04OCfZ3jzwzZHVdiIxwThUjI6vpe1hk)

Carpentry Fundamentals: (

-https://www.youtube.com/watch?v=sPnpU8Y_chU\u0026list=PLh04OCfZ3jzzuRE2jHVUH4DpwXtbCLZIa)

Build a Deck with Integrated Pergola (

-https://www.youtube.com/watch?v=xC0ZwiMe1O8)

Nudura One Series (

-https://www.youtube.com/watch?v=fTH7VZUqLXU)

➤FOLLOW US on Social Media:

Instagram –

-http://www.instagram.com/uptokode

Facebook –

-http://www.fb.com/UpToKode

Twitter –

-http://www.twitter.com/UpToKode

Website –

-http://uptokode.ca/

➤TOOLS – MATERIALS (Affiliates):

Makita 5pc Combo Kit 18V –

-https://amzn.to/3ki8EHg

Makita 2.5hp Air Compressor –

-https://amzn.to/3651Fy7

Bosch Hammer Drill –

-https://amzn.to/2Gk0dg8

Cadex 21 Gauge Nailer –

-https://amzn.to/3kPsaf1

Paslode 16 Gauge Finish Nailer –

-https://amzn.to/3jcDO3g

Stabila Rotary Laser Level –

-https://amzn.to/3csW9GA

Stabila 6′, 4′, 2′ Levels –

-https://amzn.to/36i6ft1

OLFA Utility Knives –

-https://amzn.to/3kMcVTW

Stanley Tape Measures –

-https://amzn.to/3j4tryf

Tajima Chalk Lines –

-https://amzn.to/3kOgxom

Marshalltown Drywall/Plastering Trowel –

-https://amzn.to/36egezs

GRK 2 3/4″ Concrete Screw –

-https://amzn.to/32fRvbg

Tytan Window \u0026 Door Spray Foam 24oz –

-https://amzn.to/3kVOcx3

Stiletto 14oz Hammer w/ Poly Handle –

-https://amzn.to/36aWH1f

➤FILMING EQUIPMENT (Affiliates):

DJI Ronin S Gimbal for DSLR –

-https://amzn.to/2JaRUEY

DJI Mavic Air Drone –

-https://amzn.to/3e4xlWg

DJI Osmo Mobile 3 Gimbal –

-https://amzn.to/34BtYmC

Rode Link Mic for DSLR –

-https://amzn.to/34BQN9y

Saramonic Blink 500 Microphone –

-https://amzn.to/2GfvTE4

Joby Grip Tight PRO 2 Phone Holder –

-https://amzn.to/2HHXw9c

Vanguard Tripod –

-https://amzn.to/35OA42t

➤GEAR (Affiliates):

Carhartt Carpenter Pants –

-https://amzn.to/308pQrD

Occidental Leather Belts –

-https://amzn.to/2Ewa8yV

HyFlex Nitrile Coated Cotton Gloves –

-https://amzn.to/3l5ByLN

UVEX Safety Glasses –

-https://amzn.to/3i0nelH

Laser Lite Ear Plugs –

-https://amzn.to/3j0UtXt

Keen Work Boots –

-https://amzn.to/2U2yeVT

Smartwool Socks –

-https://amzn.to/3jY6bl1

Helly Hansen Work Pants –

-https://amzn.to/3p1hTiA

➤Watkins ICF Hangers

USE PROMO CODE – UPTOKODE2020 and receive 10% Discount when ordering

Watkins Hangers direct at www.watkinshanger.com

**SUBSCRIBE** and stay tuned for our upcoming series on “Nudura One Series” and “Decks and Pergolas”

#ICF #customhomes #generalcontracting #drywall #DIY #tutorial #howto #doityourself #homebuilding #carpentry #carpenter

keywords: #flushbeam, #loadbearingwallremoval, #wallremoval, #structuralengineering, #Denver

How to remove a load bearing wall using a flush beam approach. The home owner got poor advice from a contractor leading to a sloping ceiling shortly after removing the wall. After calling LEVEL, it was recommended by our lead engineer to install two flush beams to carry the load down to the foundation.

We teamed up with Construction Services of Denver to complete the work. LEVEL provided the structural engineering and design plan, while Construction Services of Denver completed the installation and construction.

This not only provided Roberto (the homeowner) with peace of mind but also allowed him to have a perfect view to his beautiful lake.

If you have any questions or concerns, give us a call. We would love to help make your vision a reality.

720.408.0119

-https://www.levelinspectionsco.com/

keywords:

See more articles in category: FAQS