Top 15 how do i backwash my pool

Below is the best information and knowledge about how do i backwash my pool compiled and compiled by the hkfindall.com team, along with other related topics such as:: how long to backwash pool, how often to backwash pool with algae, how to backwash above ground pool, backwash vs rinse, what to do after backwashing pool, where does backwash pool water go, pool backwash diagram, how to backwash de pool filter.

how do i backwash my pool

Image for keyword: how do i backwash my pool

The most popular articles about how do i backwash my pool

How to Backwash Your Pool Filter—The Easy Way

  • Author: poolpartstogo.com

  • Evaluate 4 ⭐ (23044 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Backwash Your Pool Filter—The Easy Way 1. First, turn off the filter system. · 2. Then, connect the backwash hose to the filter’s waste port. · 3. Turn the multiport valve to “Backwash.

  • Match the search results: 2.     Then, connect the backwash hose to the filter’s backwash port. This will be the hub of where the backwash really happens.

  • Quote from the source:

How to Backwash a Pool Sand Filter & How Often to Do It – My …

  • Author: www.myperfectpool.com.au

  • Evaluate 4 ⭐ (22789 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Backwash a Pool Sand Filter & How Often to Do It – My … Switch off the pool pump. · Select the BACKWASH setting on the filter valve. · Turn the pump back on and backwash until for 2 minutes or until the water runs …

  • Match the search results: Backwashing clears out the dirt and gunk from your pool’s filter. Whether you have a sand filter or a DE filter, it will need backwashing from time to time. In this article I’ll tell you why you need to backwash, when to backwash and give you step-by-step instructions on how to backwash …

  • Quote from the source:

How to backwash a pool sand filter. – Pinch A Penny

  • Author: pinchapenny.com

  • Evaluate 4 ⭐ (25257 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to backwash a pool sand filter. – Pinch A Penny Roll out your backwash hose to someplace that the water can go. · Turn off your pump at the breaker · Set the multiport valve to backwash · Turn the pump back on …

  • Match the search results: If you notice that your pool water is not as clear as it used to be, it may be time to clean your filter. If you have a sand filter, this process is called backwashing. In order to check if your filter needs to be backwashed, take a look at the pressure gauge. There will be a place that marks the no…

  • Quote from the source:

How to Backwash a Pool Filter The Right Way – Swim University

  • Author: www.swimuniversity.com

  • Evaluate 3 ⭐ (16031 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to Backwash a Pool Filter The Right Way – Swim University How to Backwash Using a Multiport Valve · Attach the backwash hose to the waste or backwash port. · Turn the filter system off. · Turn the …

  • Match the search results: When the pressure gauge reads 10 pounds per square inch (psi) above the normal operating level, it’s time to backwash. If it reads more than 10 psi over the normal level, it’s really time to backwash.

  • Quote from the source:

How to Backwash Your Swimming Pool Filter – Pool Research

  • Author: poolresearch.com

  • Evaluate 4 ⭐ (32235 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Backwash Your Swimming Pool Filter – Pool Research How to Backwash a Sand Filter · 1. Turn Off the Pump · 2. Switch the Setting on the Valve · 3. Attach the Backwash Hose · 4. Turn the Pump Back On · 5. Turn Off the …

  • Match the search results: Then, position the backwash hose where you would like the water to discharge. If you don’t have a backwash hose, check out my article on the best pool backwash hoses.

  • Quote from the source:

When to backwash your pool – Eco Outdoor

  • Author: www.ecooutdoorusa.com

  • Evaluate 4 ⭐ (24368 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about When to backwash your pool – Eco Outdoor How to backwash a pool’s filter · Turn off your pool’s pump and filtration system. · Clamp the backwash hose to your water outlet. · Set the filter …

  • Match the search results: As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure. For example, if …

  • Quote from the source:

How To Backwash A Pool – Our Complete Guide (Infographic)

  • Author: www.poolassist.com.au

  • Evaluate 3 ⭐ (9740 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How To Backwash A Pool – Our Complete Guide (Infographic) Backwashing is the process of reversing the flow of water into the pool’s filter, flushing the filter medium (sand or DE), and then expelling …

  • Match the search results: So how often should you backwash a pool? In this post, we’re going to show you step-by-step when and how to backwash a pool filter to ensure that the rest of your maintenance is optimised.

  • Quote from the source:

How to backwash your pool – a step-by-step guide – Eagle …

  • Author: eagleleisure.co.uk

  • Evaluate 4 ⭐ (25394 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to backwash your pool – a step-by-step guide – Eagle … But backwashing is what we call it when you reverse the the flow of water through the filter. Instead of the water flowing through the filter and into the …

  • Match the search results: But ideally, the less time you can backwash for the better. Backwashing pulls water out the swimming pool. This will then need to be topped up and reheated. So the more water is used during backwashing – the more energy and money is used to run the swimming pool.

  • Quote from the source:

Guide to Backwashing Your DE Pool Filter – SwimmingPool.com

  • Author: www.swimmingpool.com

  • Evaluate 3 ⭐ (9532 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Guide to Backwashing Your DE Pool Filter – SwimmingPool.com How to Backwash a DE Pool Filter · Step 1: Turn off pool equipment. · Step 2: Rotate the valve to the “Backwash” position. · Step 3: Turn equipment back on and run …

  • Match the search results: For slide valves, turn backwash handle and pull the valve piston straight up to the backwash position. Lock it into position so it doesn’t slide up during operation. For multiport valves, push the handle down and rotate valve to the backwash position. Be sure the handle is pressed down all the way a…

  • Quote from the source:

3 signs your pool filter needs to be backwashed – Swimart

  • Author: swimart.com.au

  • Evaluate 4 ⭐ (29269 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about 3 signs your pool filter needs to be backwashed – Swimart Not exactly sure what that means? Well, as the name suggests, backwashing involves reversing the flow of water through your filter media, be it …

  • Match the search results: Knowing when to backwash your filter is really important in keeping your pool water clean and filtration equipment in peak condition. The good news is that there are three common signs that indicate if and when your pool filter needs to be backwashed. They include:

  • Quote from the source:

How to clean the swimming pool filter sand and backwash

  • Author: www.pahlen.com

  • Evaluate 4 ⭐ (21148 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to clean the swimming pool filter sand and backwash Cleaning and backwash the filter · Stop the pump. · Close the valves on the suction and return lines. · Open the cover of the pump and empty the filter basket.

  • Match the search results: After about 5-10 days, or when the reading of the pressure gauge on the pump side of the filter has increased by about 0.2 bars (20 kPa, 3 psi) since the last backwash, backwash the filter as follows:

  • Quote from the source:

How to Clean and Backwash Your Filter – Poolside North Shore

  • Author: poolsidenorthshore.co.nz

  • Evaluate 4 ⭐ (33951 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Clean and Backwash Your Filter – Poolside North Shore Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and …

  • Match the search results: Over time, the pool filter will be clogged by various waste elements which will impede its ability to perform optimally. To clean out such debris, the backwashing setting has to be implemented.  To perform backwashing on your filter, follow the steps below.

  • Quote from the source:

How Often Should You Backwash Your Pool?

  • Author: www.poolandpatiopros.com

  • Evaluate 3 ⭐ (16047 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How Often Should You Backwash Your Pool? Backwashing is a filter cleaning process through your filter system that reverses the flow of water. Pool filters allow the removal of organic …

  • Match the search results: The question “how often should you backwash your pool” is often on every pool owner’s mind. You have to do a backwash if you want to clean your pool and ensure your filtration runs efficiently. This article will teach you what backwashing is, how to do it, and how often to do it.

  • Quote from the source:

How To Backwash A Pool Sand Filter

  • Author: www.trojanpoolservices.com.au

  • Evaluate 4 ⭐ (32933 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How To Backwash A Pool Sand Filter As sand filters are not as effective as cartridge filter in removing finer particles, it’s important to backwash on a frequent basis. A good rule of thumb is to …

  • Match the search results: A good rule of thumb is to backwash once the pressure displayed on your pressure gauge is 8-10 psi over the starting level. Most pressure gauges on sand filters have a red and green zone.

  • Quote from the source:

How do I backwash my swimming pool – Water Plant

  • Author: www.waterplant.co.za

  • Evaluate 4 ⭐ (24560 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How do I backwash my swimming pool – Water Plant Connect your backwash hose to your filter or open any valves on the waste line and be prepared for water to come gushing out. Turn your pump …

  • Match the search results: There are three types of pool filters: sand filters, diatomaceous earth filters and cartridge filters. In the case of the latter, you won’t be performing any backwashing as they do not have this functionality. However, a sand filter and DE filter can and should be backwashed. For a sand filter, the …

  • Quote from the source:

Multi-read content how do i backwash my pool

Share this…

  • Facebook
  • pinterest
  • Twitter
  • LinkedIn

Backwashing cleans dirt and grime from your pool filter. Whether you have a sand filter or a DE filter, it will need to be backwashed from time to time. In this article, I’ll tell you why you should backwash, when to backwash, and give you step-by-step instructions on how to backwash your pool filter.

To backwash, filter sand or DE, turn off the pool pump and attach the backwash hose. Then set the valve to “backwash”, turn the pump back on and let the water run until the water runs clear (usually about 2 minutes). Then you will need to set the valve to drain after about 30 seconds. If you have a DE filter, you will load DE.

This is the extremely short version, of course. There is much more than that. In this article we cover indoor pool, above ground pool, salt water pool. Plus, you’ll find that these processes will work for many brands, including:

  • Pentair
  • Intex
  • Hayward
  • Jandy
  • RX is clear
  • Astral

Backwashing a pool filter.Use a multiport valve to backwash the pool filter. The photo shows a fairly standard pool filter, pump and plumbing.

What is backwashing?

Shows what backwashing is and how it works. The image on the left demonstrates regular filtering, the image on the right shows what happens when you backwash your pool.The image on the left shows the usual filtering. Dirty pool water runs down through the sand, impurities are trapped, then the water rises through the side tubes and hoses to the pool. Backwashing is the opposite (right figure). Pool water passes through the riser and exits the side edges at the bottom, then returns through the sand lifting impurities. Then it will come out through the waste outlet and carry away impurities and dirt.

Backwashing or backwashing reverses the flow of water through the pool filter, lifting and discharging the filter media (sand or DE), then pushing the dirty water through the discharge line into the ground or drain. This is sometimes called backflushing.

Backwashing is basically the process of cleaning the pool filter and should be done regularly. More on that later.

To prevent backflow into the pool, after backwashing is complete, you must rinse the filter. Just as backwashing lifts and rinses sand, backwashing holds sand in its original position for optimal filtration.

Read on to find out how to backwash your pool.

Why should you backwash?

All DE (diatomaceous earth) and sand filters use the same basic mechanism: when set to “Filter”, water flows out of the pool, through the filter, and back into the pool. The filter media (sand or DE) inside the filtration system traps debris, dirt and oil. A typical pool multiport system has 6 different settings – filter, backwash, rinse, recirculate, shut off and trash.

However, over time, or when you vacuum your pool, dirt and debris settle in the filter causing the filter to become dirty and clogged with contaminants. If left unchecked, it will reduce the cleaning ability of the filter and, if left on, can restrict water flow and put additional pressure on the pool.

How to Backwash a Sand Filter

Internals of a pool sand filter.Diagram showing the inner workings of a swimming pool sand filter.

Pool sand filters use sand to filter contaminants in your pool water. Pool water circulates through specially filtered pool sand.

Sometimes you will need to clean your sand filter by backwashing it. Here’s how to backwash the sand filter:

  1. Turn off the pool pump.
  2. Place the sand filter valve handle in the BACKWASH tank position and ensure the handle locks into place.
  3. Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located above the filter) comes out clear.
  4. Turn off the pump.
  5. Set the filter valve handle to the RINSE position and make sure the handle locks in place.
  6. Turn on the pump and run the wash for 30-60 seconds or until the water in the glass runs clear.
  7. Turn off the pump.
  8. Close the skimmer valves to prevent water from entering the filter from the pool. Pour the filter into the basket and clean the feather catcher.
  9. Reinstall and seal the skimmer basket and hair catcher.
  10. Reopen the skimmer valve.
  11. Reset the filter valve on the filter and make sure the handle locks in place.
  12. Turn on the pump.

How to backwash a DE filter.

Powder Diatomaceous Earth (D.E.) for DE FiltersThe image shows Diatom Earth or D.E. is the filter media inside the D.E. pool filter.

The DE filter uses diatomaceous earth (DE for short) instead of sand to capture contaminants. D.E. is a much finer medium than sand and therefore filters your pool water better. However, additional maintenance is required when backwashing.

Backwashing a D.E. Filter is similar to a sand filter with an additional step of encapsulating diatomaceous earth.

Important:Before you begin, make sure you have D.E. powder available, as you will need to refill the filter after backwashing. DE is removed by backwashing.

How to backwash the DE filter (with multiport valve):

  1. Turn off the pool pump.
  2. Select the BACKWASH setting on the filter valve.
  3. Turn the pump back on and backwash for 2 minutes or until the water comes out clear (you can check this in the sight glass on the side of the filter).
  4. Turn off the pump.
  5. Select the RINSE setting on the filter valve.
  6. Turn the pump back on and flush for 1-2 minutes. You can repeat steps 2-6 several times if the filter is particularly dirty.
  7. Turn off the pump and select FILTER
  8. Refill D.E. flour.
  9. Check the manufacturer’s instructions to find out how much it costs. It will probably be 3-6 lbs (or about 80% of the filter’s full capacity). Typically, you would add it to the skimmer (mix DE with water first) and/or add some D.E. powder to the pump filter and the rest to the skimmer. Check the manufacturer’s instructions again. Run the pump on the FILTER setting for 30 minutes or more to allow D.E. powder to recoat the strainer.

How to backwash the DE filter (with push-pull valve):

The backwashing procedure for DE filters with ejector valves is almost the same as backwashing for DE filters with multiport valves.

  1. Turn off the pool pump.
  2. Open the valve for BACKWASH.
  3. Turn the pump back on and backwash for 2 minutes or until the water comes out clear (you can check this in the sight glass on the side of the filter).
  4. Turn off the pump.
  5. Close the push/pull valve.
  6. Fill D.E. flour.
  7. Check the manufacturer’s instructions to find out how much it costs. It will probably be 3-6 lbs (or about 80% of the filter’s full capacity). Typically, you would add it to the skimmer (mix DE with water first) and/or add some D.E. powder to the pump filter and the rest to the skimmer. Check the manufacturer’s instructions again. Run the pump for 30 minutes or more to allow D.E. powder to recoat the strainer.

Can you wash the cartridge filter again?

Pool cartridge filterPool cartridge filter replacement cartridge.

Pool cartridge filters cannot be backwashed unlike sand filters and D.E. filters. Cartridge filters are not designed to work “in reverse”.

However, the cartridge filter can and should be cleaned regularly. To clean the cartridge filter, you will need to open the filter and remove the cartridge. Rinse and spray the canister with hose every 4 weeks and give it a deep clean every few months.

We have full instructions for deep cleaning your canister filter in our blog here:
How to Clean a Swimming Pool Cartridge Filter (Using Hydrochloric Acid)

How long does it take to backwash the pool?

As a general rule, whether you have a sand filter or a DE filter, you should rinse your pool about once a week during swimming season. The optimal time is right after youswimming pool vacuum. If your pool has been used more than usual, it may need to be rinsed again twice a week.

We recommend thispass the voidand thatcleaning robot.

Also, if your pool is particularly sensitive to leaves, backwashing may be necessary more often due to leaves, other plant debris and contaminants from birds, etc. will seep into your pool.

You can also tell when to backwash by checking the filter pressure gauge. Normal operating pressure is between 50 – 170 Kpa (kilopascal) or 10 – 25 psi. However, when the sand is dirty and clogged, the pressure increases.

Typical pool filter pressure gauge.When should you backwash your pool? Use the filter pressure gauge as a guide. It’s time to backwash when the pressure rises 8-10 psi above normal or above 80 Kpa.

If the pressure on the meter reads 5-10 psi higher than normal, it’s time to backwash.

If you have attended your pool being washed and the pressure is still high, check out our article:8 Reasons Filtration Pump Pressure Is High (And How To Fix It)

When is it not necessary to backwash?

If your pool has an unusually high amount of dirt (for example, due to a construction site nearby, because it was unexpected and left uncovered for a long time, or it could be caused by running water ) by flooding), you should probably skip the whole filter.

This is also the case if your water has or has had an algae problem. Live algae easily pass through the filter sand and back into the pool. And the same goes for the algae that die after the shock treatment. You can learn more aboutprevent algae here.

In these cases, instead of vacuuming and backwashing, it may be better to vacuum directly into the WASTE and deliver the vacuumed water directly down the drain.

Where to find backwash water

When you backwash your pool, there will be a lot of water to deal with. You need to have a plan before you start. A few hundred gallons of water spilled on your neighbor’s house will probably keep you from being invited to his next Christmas party.

Your yard

You should backwash your backyard pool. You will find in many states and councils that it is illegal to empty pool water into a drain or sewer.

However, be sure to keep the water in your property. Some councils offer fines if the pool water runs dry.

Will it kill grass or plants?In most cases, your weed will be fine if you pour some backwash on it. You might consider moving the faucet when you flush the toilet, so the water doesn’t stay in one place.

Also, make sure he won’t rush into your house or anywhere else.

As for plants, pool water will kill some plants, but many will be fine, as long as there is not too much water in the pool.

Gutters or storm drains

In many places it isIllegal emptying of the swimming poolin a street, gutter or storm sewer unless it has been decontaminated. This water is usually found in rivers, streams, lakes and oceans. Pool water often contains a variety of chemicals that can be harmful to the local environment.

Sanitary Drainage by Cleanout

In some areas you can rinse the pool here. Even so, it is generally not acceptable for your pool to permanently sink into the drainage system. Check with your town hall to find out if this is an option for you.

Important tips for backwashing

  • One of the downsides of backwashing is that because water is forced out of the system and turned into waste, it also…wastes…water. Although this is unavoidable, the key to not over-washing and rinsing out more water than necessary is to carefully monitor the color and quality of the water in the viewfinder.
  • Do not backwash more than necessary or longer than necessary. Sand filtration systems are most effective in the middle of the filtration cycle. This is partly due to the position of the sand in the filter, at any given time, and partly due to the cyclical accumulation of dirt and debris collected in the filter. The real impact is that backwashing too much or too often will actually reduce the effectiveness of the sand filter.
  • Because backwashing inevitably removes some of the sand along with dirt and debris, it will be necessary to replenish the sand in the filter from time to time. As you add more sand, run the filter on RINSE for about a minute to reduce the amount of sand going back into the pool. We recommend this
  • Replace filter sand here
  • .
  • Finally, always be sure to turn off the pump before moving or resetting the filter valve settings. Otherwise, you risk damaging and possibly destroying the system.

Recommended products

Pool sand filter

Spare filter sand

Pool vacuum -Automatic vacuum cleanerWhererobot cleaner

Related Reading:How to remove sand from the poolCloudy pool water: why

Beach ball in pool at My Perfect Pool

Popular questions about how do i backwash my pool

how do i backwash my pool?

To backwash a sand filter:Shut off the system.Clamp the backwash hose to the water outlet.Position the backwash valve to either push or pull—the water will flow through the hose or the equipment.Turn the handle to the backwashing position.Backwash for a few minutes or until the water clears.

How do you backwash a swimming pool?

How do you backwash a pool step by step?

When should I backwash my pool?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

How long do you run the backwash on a pool?

Open the air bleeder assembly on your filter and turn pump on. Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 – 3 minutes, or until water runs clear.

Does backwashing remove water from pool?

The backwashing process reverses the flow of water to flush out contaminants from a swimming pool filter. It should be carried out until water runs clear through the waste line.

What is the difference between backwash and rinse?

Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.

What does backwash look like?

Do you lose sand when backwashing?

Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs. In general, you shouldn’t be losing sand from your sand filter. Nor should any sand be coming out during backwashing, rinsing or filtering.

How do you rinse after backwash?

How do you backwash a pool with a garden hose?

Why am I having to backwash my pool so often?

That said, many pool owners backwash weekly as part of their summer maintenance routine, often after they vacuum to collect the remaining particles that are often stirred up.

How long do you backwash a DE filter?

Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.

Can you backwash a sand filter too much?

Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.

What does backwashing a sand filter do?

The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value’s waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.

Video tutorials about how do i backwash my pool

keywords: #poolcare, #backwashpool, #cleanpoolfilter

If you ever experience problems with your pool filter, backwashing can help clear them up and restore your water flow. This video shows all the steps to take to backwash your filter and get your pool back in shape. Find more pool care tips and products at Cabanapools.com.

keywords: #filterbackwashing, #howtobackwashyourfilter, #FNSplusfilterbackwashing, #Haywardfilterbackwash, #Jandyfilterbackwash, #poolfiltercleaning, #backwashingtechniques, #Selectaflowbackwashing, #Selectaflowbackwash, #yt:crop=16:9

WEBSITE:

-http://www.swimmingpoollearning.com/

YouTube Video Index — A list of all of my videos:

-http://poolmandave.blogspot.com/2014/03/swimming-pool-tips-reviews-how-to-video.html

For my latest updated Backwashing video which goes into more detail please see:

How To Backwash Your D.E. Filter – The Ultimate Guide:

-http://youtu.be/j3CleipKc5A

BRAND SPECIFIC FILTER CLEANING:

Pentair 4000 series:

-http://youtu.be/XWIltRenwC8

Cleaning a D.E. filter Top Manifold (Jandy, FNS, Hayward, Titan) D.E. leaking into pool:

-http://youtu.be/2DOBqlji8fk

RELATED VIDEOS:

How Much D.E. (Diatomaceous Earth) do I Add?:

-http://youtu.be/lz97RnlATi0

Backwashing a Pentair 4000 Series Filter (2000 Series):

-http://youtu.be/dbf9b9l6e98

Backwashing a Sand Filter:

-http://youtu.be/yA4HcOEOi5I

Backwash Valve troubleshooting, changing the piston:

-http://youtu.be/LfxjwhbANoQ

Hayward Mutliport backwash valve troubleshooting:

-http://youtu.be/3f6v7IbzjUU

Installing a Pentair Cartridge Filter (Clean \u0026 Clear Plus):

-http://youtu.be/RVXcdHg4Y3w

Cloudy Pool Water, Causes and Cures:

-http://youtu.be/R2of9Kg8PV4

Pool Filter Comparison, Filter Types:

-http://youtu.be/WK2_BDwnfTE

NOTES:

This is how you backwash your D.E. pool filter if you have the push pull valve. At the end I also show you how to backwash with a Hayward Selecta-flo valve. With regular filter cleaning (every 6 months) you shouldn’t need to backwash often. But if the pressure is high and/or flow is low, a backwash will get everything running again.

WEBSITE:

-http://www.swimmingpoollearning.com/

Mrdgvb1 Social Media Links:

Google +:

-https://plus.google.com/b/107735343574734346096/

Blogger:

-http://poolmandave.blogspot.com/

Facebook:

-https://www.facebook.com/pages/Youtube-Mrdgvb1/381257741926763?ref=hl

If you found this video helpful, please visit my website, any donation is greatly appreciated.

WEBSITE:

-http://www.swimmingpoollearning.com/

keywords:

keywords:

https://in.pinterest.com/pin/how-to-backwash-pool-google-search–279293614382439795/

See more articles in category: FAQS

Maybe you are interested

Sale off:

Best post:

Categories